The cost: $0 and 20 easy minutes of your time.MOST INCREDIBLE EXPERIENCE WITH EUGENE - he is unlike any other appliance salesman I have ever met. Test it and once positioned where it works reliably, glue the shim into place (Elmers is fine). To wedge the shim into place, you’ll need a small crowbar or screwdriver to create the needed gap to slide the shim into place. You goal is to force the top of the housing to push downward about an 1/8″ so that the door strike (the fin) will hit the switch when the door is closed. SOLUTION: Place a shim (perhaps 3/8″ thick or so) between the countertop and the top center of the housing (just above the strike plate switch). Remove the knife and the unit will stop (simulating a door open condition). If the dishwasher comes on, then you know this is your problem. While the door is open, use a knife to depress the switch on the housing of the unit (where the fin would normally strike the switch). To test this, reset the unit by pressing and holding the START button for 3 seconds. Thus, the strike misses the switch by striking just below the switch. The reason it is not hitting the switch is because when the dishwasher was mounted to the underside of the counter top, the screws drew the top of the housing ever so slightly upward and caused the top of the unit to bow. The problem in my case is that the strike was not hitting the switch (attempting to strike below the switch) If you use a flashlight, it’s hard to tell but it is detectable. When the door is shut, the strike (fin) depresses a switch on the dishwasher’s housing. PROBLEM: The dishwasher door has a plastic strike that is shaped like a fin. Here’s what my problem was and is likely what is happening with many of these GE dishwashers. I had this blinking light problem on a GE GDF520PGD2WW dishwasher where when you push the START button, the unit would not come on and after a few seconds the green light would start to blink. What to Do When the Dishwasher Won’t Startĭo you have other troubleshooting methods for a dishwasher that won”t start? Please lend a hand to all of the people that read this page seeking help and leave your troubleshooting method below. If you have tested and confirmed working all the other steps above, then the control board in your dishwasher is most likely bad and replacing it would be a smart option at this point. If your dishwasher won’t start, this could mean that the board is bad. The control board in your dishwasher supplies power to all components. To determine if your door latch is bad, inspect your dishwasher door and be sure the latch is not broken. If this latch becomes broken or cracked, it will prevent your door from closing properly. 99% of the time this latch is made from plastic. The part that holds your dishwasher door shut is called a door latch. To determine if the thermal fuse is bad, remove the control panel, locate the fuse, and test it for continuity. Most dishwashers have the thermal fuse located in the control panel area. If this fuse blows, it will need to be removed and replaced to make your dishwasher work. This fuse is designed to blow if the dishwasher overheats. To determine if the door switch is bad, remove the control panel, locate the door switch, and test it for continuity.Īnother part in your dishwasher that could be causing it to not start could be the thermal fuse. This switch is located inside the door panel. If your dishwasher won’t start, then it is possible this switch is bad. This switch is a safety feature and makes it so the dishwasher will not run if the door is open. This door switch is also sometimes called a door lock or door interlock switch. The next thing that could be causing your dishwasher to not start could be the door switch. (To be sure the outlet is getting power you can unplug the dishwasher and plug something else in to be sure the outlet is getting power.) If the dishwasher is plugged in and the GFI has not tripped, then check the breaker on the wall and make sure it has not tripped and is in the on position. If the outlet the dishwasher plugs into is a GFI outlet, make sure it has not tripped. If your dishwasher does not light up or is not getting power, check where the dishwasher plugs into the wall. Using this guide to troubleshoot your dishwasher works for all dishwashers on the market today. Note: The majority of dishwashers (whether Maytag, Kitchen Aid, Frigidaire, Kenmore, Whirlpool, and Bosch) work the same way. The issues below are listed in order of most probable causes starting at the top of the list. You can follow the steps below to repair your dishwasher and get it working again. The most common problems with a dishwasher not getting power or lights not turning on are listed below. If your dishwasher won’t turn on or start, here are a few things to check yourself before calling a technician.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |